My contact person
Select location

After selection of your ZIP code, we designate the relevant staff to attend to you at once.

Gears and Gear racks

The gears made of tribologically optimised iglidur® high-performance polymers impress with their significantly higher service life than gears made of comparable plastics.
Due to fine-tuned additives of reinforcement materials and solid lubricants, they do not require additional lubrication.
In the industry's largest test laboratory, the gears made of iglidur® materials are thoroughly tested to continuously improve their service life.

Due to order peaks, the delivery time for single items is 10-15 working days longer than stated. Please refer to our order confirmation for the specific delivery date. For urgent, short-term requirements, please contact us personally so that we can realise the delivery time necessary for you. You will find your contact person at the top of the menu under "My contact person", next to the language/country selection, or on this page.

Number of products: 19

New

iguform S270 gears, mm

  • Low coefficient of friction
  • Low humidity absorption
  • Low-noise

8 different modules available. Choose from over 300 dimensions.

Matching gear racks available here

For information on tolerances, please refer to the product description.
1.96 USD/Pc.
317 items, thereof ready for shipping:
313 in 48 hours
To the product page
New

iguform S270 gear racks, mm

  • Low coefficient of friction
  • Low humidity absorption
  • Low-noise

Matching modules available for the gear product range.

You will find information on the length in the product description.
Upon request
8 items, thereof ready for shipping:
8 in 4 weeks
To the product page
New

igutek P360 gears, mm

  • Increased wear resistance
  • Good tribological specifications
  • Very robust
  • Resistant to shock loads

8 different modules available. Choose from over 300 dimensions.

Matching gear racks available here

For information on tolerances, please refer to the product description.
2.26 USD/Pc.
317 items, thereof ready for shipping:
315 in 48 hours
To the product page
New

igutek P360 gear racks, mm

  • Increased wear resistance
  • Good tribological specifications
  • Very robust
  • Resistant to shock loads

Matching modules available for the gear product range.

You will find information on the length in the product description.
6.01 USD/Pc.
8 items, thereof ready for shipping:
8 in 4 weeks
To the product page

xirodur® B180, gear, mm

  • ​​​​​​Very low coefficients of friction
  • Wear-resistant material for continuous operation
  • Vibration-dampening
  • Available in 3 hub designs

Matching gear racks available here
9.75 USD/Pc.
9 items, thereof ready for shipping:
6 in 24 hours
To the product page

iguform S270 bevel gears - gear ratio 1:1

  • Low coefficient of friction
  • Low moisture absorption
  • Quiet operation

Please note: In order to achieve the desired transmission ratio, two bevel gears must be ordered.
The bevel gears listed here (1:1) can be combined with each other. Please make sure to select the same module.
Upon request
8 items, thereof ready for shipping:
8 in 48 hours
To the product page

iglidur® A500 gear, mm

  • The endurance runner at higher temperatures in the food sector
  • Compliant with Regulation (EU) No. 10/2011
  • FDA compliant
  • Temperature resistant from -100°C to +250°C

iguform S270 bevel gears - gear ratio 1:3

  • Low coefficient of friction
  • Low moisture absorption
  • Quiet operation

Please note: In order to achieve the desired transmission ratio, two bevel gears must be ordered.
The bevel gears listed here (1:3) can be combined with each other. Please make sure to select the same module.
Upon request
8 items, thereof ready for shipping:
8 in 48 hours
To the product page

iguform S270 bevel gears - gear ratio 1:5

  • Low coefficient of friction
  • Low moisture absorption
  • Quiet operation

​​​​​​​Please note: In order to achieve the desired transmission ratio, two bevel gears must be ordered.
The bevel gears listed here (1:5) can be combined with each other. Please make sure to select the same module.
Upon request
2 items, thereof ready for shipping:
2 in 48 hours
To the product page

igutek P360 bevel gears - ratio gear 1:4

  • Increased wear resistance
  • Good tribological specifications
  • Very tough
  • Resistant to shock loads

Please note: In order to achieve the desired transmission ratio, two bevel gears must be ordered.
The bevel gears listed here (1:4) can be combined with each other. Please make sure to select the same module.
Upon request
6 items, thereof ready for shipping:
5 in 48 hours
To the product page

iguform S270 bevel gears - gear ratio 1:1,5

  • Low coefficient of friction
  • Low moisture absorption
  • Quiet operation

Please note: In order to achieve the desired transmission ratio, two bevel gears must be ordered.
The bevel gears listed here (1:1.5) can be combined with each other. Please make sure to select the same module.
Upon request
2 items, thereof ready for shipping:
2 in 48 hours
To the product page

igutek P360 bevel gears, ratio gear 1:2

  • Increased wear resistance
  • Good tribological specifications
  • Very tough
  • Resistant to shock loads

Please note: In order to achieve the desired transmission ratio, two bevel gears must be ordered.
The bevel gears listed here (1:2) can be combined with each other. Please make sure to select the same module.
Upon request
10 items, thereof ready for shipping:
10 in 48 hours
To the product page

igutek P360 bevel gears - gear ratio 1:1,5

  • Increased wear resistance
  • Good tribological specifications
  • Very robust
  • Resistant to shock loads

Please note: In order to achieve the desired transmission ratio, two bevel gears must be ordered.
The bevel gears listed here (1:1.5) can be combined with each other. Please make sure to select the same module.
Upon request
2 items, thereof ready for shipping:
2 in 48 hours
To the product page

iglidur® F, gear, mm

  • Electrically conductive 
  • High compressive strength
  • Good temperature resistance
  • Available in 3 hub designs

igutek P360 bevel gears - gear ratio 1:1

  • Increased wear resistance
  • Good tribological specifications
  • Very tough
  • Resistant to shock loads

Please note: In order to achieve the desired transmission ratio, two bevel gears must be ordered.
The bevel gears listed here (1:1) can be combined with each other. Please make sure to select the same module.
Upon request
8 items, thereof ready for shipping:
8 in 48 hours
To the product page
The terms "igus", "Apiro", "CFRIP", "chainflex", "conprotect", "CTD", "drygear", "drylin", "dryspin", "dry-tech", "easy chain", "e-chain", "e-chain systems", "e-loop", "e-ketten", "e-kettensysteme", "e-spool", "e-skin", "flizz", "ibow", "igear", "iglidur", "igubal", "kineKIT", "manus", "motion plastics", "pikchain", "plastics for longer life", "print2mold", "readycable", "readychain", "ReBeL", "robolink", "speedigus", "tribofilament", "triflex", "xirodur" and "xiros" are legally protected trademarks of the igus® GmbH/Cologne in the Federal Republic of Germany, and, where applicable, in some foreign countries.
igus® GmbH points out that it does not sell any products of the companies Allen Bradley, B&R, Baumüller, Beckhoff, Lahr, Control Techniques, Danaher Motion, ELAU, FAGOR, FANUC, Festo, Heidenhain, Jetter, Lenze, LinMot, LTi DRiVES, Mitsubishi, NUM, Parker, Bosh Rexroth, SEW, Siemens, Stöber and all other drive manufacturers mentioned on this website. The products offered by igus® are those of igus® GmbH.